Can anyone help?
I've owned TOCA for some time with no problems, but since upgrading to
directx6 I can't get it to work properly. When I go to the circuit select
screen, it shows all tracks darkened and after a short time it shuts itself
down, I sometimes get a message saying low video memory, I've set it up to
use my 3d 2000 and Orchid Righ 3dfx graphics cards but it does exactly the
same with both. I tried re-installing TOCA a few times with no success. I'm
a little short on disk space can this cause problems?
I don't think your disk space is the culprit (though I could be wrong).
I have the same problem with TOCA after the DirectX6 update also. Though
I have plenty of disk space on my system. I have the patch installed
too. Hmm... did I run the patch after the re-install? I'm also having a
was working fine before. Anyone out there have any clues for us?
Later...
Tony Long
Quoted text (9 lines)
> Can anyone help? > I've owned TOCA for some time with no problems, but since upgrading to > directx6 I can't get it to work properly. When I go to the circuit select > screen, it shows all tracks darkened and after a short time it shuts itself > down, I sometimes get a message saying low video memory, I've set it up to > use my 3d 2000 and Orchid Righ 3dfx graphics cards but it does exactly the > same with both. I tried re-installing TOCA a few times with no success. I'm > a little short on disk space can this cause problems?I assume that you guys used the DX6core installation, as I used the
DX6Eng full installation and all seems OK except the selected track
is dark.
Quoted text (9 lines)
>Can anyone help? >I've owned TOCA for some time with no problems, but since upgrading to >directx6 I can't get it to work properly. When I go to the circuit select >screen, it shows all tracks darkened and after a short time it shuts itself >down, I sometimes get a message saying low video memory, I've set it up to >use my 3d 2000 and Orchid Righ 3dfx graphics cards but it does exactly the >same with both. I tried re-installing TOCA a few times with no success. I'm >a little short on disk space can this cause problems?Hi Yall,
Since upgrading to DX 6 TOCA takes a long time to load. I thought it locked
up but waited a min. or 2 and i started. When going to each track it also
does this. I also get the dark track layout when selecting the track at the
track selection screen but not in the screen as the track loads. I run a
P200,64Mb ram, STB riva 128, and Monster 3d in Win 98.
> Hi Yall,
> Since upgrading to DX 6 TOCA takes a long time to load. I thought it locked
> up but waited a min. or 2 and i started. When going to each track it also
> does this. I also get the dark track layout when selecting the track at the
> track selection screen but not in the screen as the track loads. I run a
> P200,64Mb ram, STB riva 128, and Monster 3d in Win 98.
I seem to have this same problem! Thought it was just my system.
--
??? ,,,
???(o o)
o00o-(_)-o00o
Mike Z was here!
Remove *** to reply
I have a problem with NICE 2 when running DirectX 6.0.
You should download the DirectX Uninstaller and then re-install DirectX 5.x...
http://home.att.net/~ebrink1/Direct.htm#DxUn
Good luck!
Seb
Michael Zamarocy schrieb:
Quoted text (16 lines)
> > Hi Yall, > > Since upgrading to DX 6 TOCA takes a long time to load. I thought it locked > > up but waited a min. or 2 and i started. When going to each track it also > > does this. I also get the dark track layout when selecting the track at the > > track selection screen but not in the screen as the track loads. I run a > > P200,64Mb ram, STB riva 128, and Monster 3d in Win 98. > I seem to have this same problem! Thought it was just my system. > -- > ,,, > (o o) > o00o-(_)-o00o > Mike Z was here! > Remove *** to replyPaul - check in Dxdiag.exe on Display Driver 2 tab that your 3D hardware has
not been disabled for D3D acceleration.
Stuart Brooks
